A leg opening can look flat on the table and still feel too tight, gape at the back, or pop stitches when you pull the garment on. The place to catch that is on a curved scrap, before you sew both legs.
Quick answer: Use the elastic type, width and cut length your pattern specifies. Match the elastic to the opening at the pattern marks, stretch the elastic only where instructed, and let the fabric feed without pulling it. For a fold-over finish, sew the elastic to the inside edge, turn it inward and topstitch with a stitch that can stretch.
Start with the pattern, not an elastic ratio
There’s no single percentage that fits every swimsuit or leotard leg. A high-cut opening and a low, full-coverage opening don’t necessarily use the same tension. Some patterns distribute the elastic evenly; others ask for less tension at the front and more around the back. Use the marks, elastic allowance and joining method in your instructions rather than dividing every opening into quarters by default.
For swimwear, use elastic designated for swimwear and follow the pattern’s material recommendation. For dancewear, check what the pattern calls for and test the feel against your skin. If the width changes, the turned edge can change too; don’t assume a wider elastic will fit the allowance.
Make a curved test with the exact layers
Trace a short curved section of the leg opening onto scraps. Use the same stretch direction as the garment and the same outer fabric, lining and elastic. A straight, unlined strip won’t tell you how the layers behave around the leg. If the pattern specifies different tension along the opening, sample the area you’re least sure about.
- Stitch a first pass. Use your pattern’s stitch recommendation. If it permits an ordinary machine zigzag, test that with the actual layers. Keep the fabric relaxed as it feeds.
- Turn the edge and finish it. Topstitch as directed. Check that the elastic stays enclosed, the edge isn’t twisted, and the lining isn’t creeping out.
- Check it flat and in motion. Let the sample relax, stretch it gently as far as the opening needs to move in wear, and release it. Look for popped stitches, a rolled edge or ripples that remain. Note your setup and change just one thing on the next sample.
Sew a fold-over leg opening
This is one common finish. If your pattern encloses elastic between layers, leaves the opening unjoined until a later step, or uses a different corner or crotch treatment, follow that sequence instead.
- Mark the opening and the elastic. Transfer front, back and other placement marks. Join the elastic into a loop only if the pattern calls for it.
- Attach the elastic to the wrong side. Align it at the edge as directed. Sew in short sections between marks, extending the elastic just enough to meet the next mark or as specified. Support the shape on the table so you aren’t pulling the fabric behind the foot.
- Fold inward and topstitch. Turn the elastic toward the inside and stitch it down using the pattern’s stretch-capable finish. Check both sides before sewing the second leg, especially where layers overlap.

If the opening waves, gaps or pops
- Wavy on the table: Check first whether the fabric was pulled while feeding. Repeat a short sample without stretching the fabric. Compare the two after they relax.
- Flat on the table but gaping on the body: Check the garment fit, elastic placement and cut length before shortening the elastic. More tension isn’t a fix for every fit problem.
- Threads pop when the edge stretches: Test a stitch that can travel with the edge, and confirm the needle suits your fabric and elastic layers. Judge the whole turned edge, not only the first row of stitching.
Choose the fabric before you tune the edge
For a project whose pattern calls for four-way stretch, start by comparing swatches such as Classic Matte Nylon Spandex in Steel Blue. Still check the pattern’s minimum stretch in each required direction. If the garment is lined, choose and test the layers together. Our stretch-fabric lining guide can help you decide what to sample from the lining collection.

Technique references: Jalie’s 3350 leg opening tutorial, Jalie’s regular-machine elastic method, and Closet Core Patterns’ two swim elastic methods. For a pattern-specific example of uneven tension, see the Bombshell leg opening sew-along.

